正常情况下,betway必威体育有自动复位功能

页面更新时间:2015-07-17 10:39 来源:未知 作者:admin 点击:

betway必威体育有自动复位功能:多个电机转动到同一位置后停止使所有分画面保持在同一画面。

Ji'nan billboard has automatic reset function: multiple motors to rotate to the same location to stop making all the points to keep in the same picture.

时间调整功能: 调整每一幅画面的停留时间。

Time adjustment function: adjust the residence time of each picture.

定时开关功能:每天最大4个时间段,停止时需保持画面停止到位

Timer switch function: every day, the maximum 4 time periods, stop when the need to keep the picture stop in place

过载保护功能:当实际画面翻转时间超过设计画面翻转时间时,系统认为电机过载并停机。

Overload protection function: when the actual picture flip over time, the system considers the motor overload and stops.

显示和修改设定参数功能:随时监控工作状态。

To display and modify the set parameter function: to monitor the working state at any time.

编辑本段安装保养1.基础支架:betway必威体育 / 应安装在牢固的金属支架或建筑物的墙面上。基础支架由购方自行设计制作,并需要严格的基础抗压和支架抗风强度计算,使之达到金属支架和betway必威体育自重对基础的抗压要求,达到当地最大风力的抗风要求。如果三面翻广告牌安装在金属支架上,应把支架背面,用铁板全部封闭,以免背后透光,影响画面效果。

Edit this section of the installation and maintenance of the 1 Basic brackets: Ji'nan advertising signs should be installed on the wall of a solid metal support or building. Support by the buyer designed, manufactured, and the need for strict based compression and support wind strength calculation, so as to achieve the metallic stents and Jinan billboards weight on the basis of the compressive requirements, meet the requirements of the local maximum wind wind. If three surface turning advertisement boards are installed in the metal stent should be the back stent, with iron all closed, to avoid light behind, affect the picture effect.

对基础支架制作精度要求:a.横梁要求水平,立柱要求竖直。b.在画面长度方向要求不平直度小于10毫米,在画面高度方向要求上下横梁不平行度小于20毫米。 对基础支架制作强度要求:下横梁是支撑betway必威体育重量的承重结构,要求在与betway必威体育连接的每一个点产生的弹性变形不得超过2毫米。

On the basis of support for the production of precision requirements: A. beam requirements level, column requirements vertical. B. in the length of the picture is required to not less than 10 mm in length, the height of the picture on the requirements of the upper and lower beams is not less than 20 mm. The based scaffold fabrication strength requirements: beam is Jinan billboard the weight of the load-bearing structure of the support, produced at each point and Jinan billboard connected by elastic deformation is not more than 2 mm.

特别提醒:基础支架设计、制作,应找具有等级资质的专业技术人员设计、制作。

Special reminder: the foundation of the design, production, should find a qualified professional and technical personnel design, production.

2.安装步骤:按尺寸要求,先装上下外框(要求外框内角为90度)固定在支架上,再将左右外框与上下框相连接,最后安装三棱柱画面。

2. Installation steps: according to the requirements of size, mounted on the first frame (request frame internal angle is 90 degrees) fixed on the bracket, the left and right frame and the lower frame are connected, finally, install the picture of the prism.

3.更换画面:首先关闭电源,将三棱柱向上提20毫米,然后从底部横向移动三棱柱,三棱柱上端就会自动脱开。

3. Change the picture: first turn off the power supply, the prism to provided 20 mm and from the horizontal movement of the bottom three prism, prism of the top will disengaged automatically.